Schneider Electric Communication Drivers User Manual

35006152 00Communication DriversInstallation manual eng

General10

ISAWAY driver100 How to select the hardware type for Windows 2000\XPProcedure After having installed and configured the driver, carry out the follow

ISAWAY driver 1012 Select the option Add/Troubleshoot a peripheral then click Next.ResultThe following window appears: 3 Select the option Add a ne

ISAWAY driver102 5 Click on Next.ResultThe following window appears: 6 Select PCX57 Device from the list then click on Next.7 Select PCX57 WDM Devic

ISAWAY driver 103How to configure hardware parameters for Windows 98Procedure When you want to modify the hardware parameters, carry out the follow

ISAWAY driver104 4 Click on Change Settings.ResultThe following window appears: 5 From the Value list, select the non-conflicting address range.Note

ISAWAY driver 105How to configure hardware parameters for Windows 2000\XPProcedure After having selected the hardware type, carry out the following

ISAWAY driver106 5 Click on Change settings. ResultThe following window appears: 6 From the Value list, select the non-conflicting address range.Not

ISAWAY driver 10710 Accept the configuration with OK.ResultThe following window appears: 11 Click on Finish to confirm hardware configuration.Step

ISAWAY driver108 How to adjust the ISA TPCX 57 card parametersAt a Glance Before installing the TPCX 57 card, you must adjust the following paramete

ISAWAY driver 109Procedure To adjust the parameters, proceed in the following manner: Example of standard address selectionThe standard address pro

111General information concerning the DriversAt a GlanceSubject of this chapterThis chapter provides general information on the drivers.What’s in

ISAWAY driver110

1119PCIWAY driver for TSX PCI 57 ••• processorsAt a GlanceSubject of this ChapterThis driver makes it possible to use TSX PCI 57 ••• processors on

PCIWAY driver112 How to install the driverAt a Glance Driver installation is a standard installation. It can be launched either:from the drivers’ CD

PCIWAY driver 113How to install the driverTo install the driver, carry out the following procedure: Start of installationInstallation byCD-ROM?Inse

PCIWAY driver114 Configuring the PCIWAY driver for windows 2000\XPAccess to the configuration toolThe configuration tool can be accessed from the ta

PCIWAY driver 115Properties Press the PCI Properties button to display the following window: The table below describes the different areas:Area Des

PCIWAY driver116 How to adjust the parameters of the TSX PCI 57 ••• cardAt a Glance Before installing the TSX PCI 57 ••• card, you must: install the

PCIWAY driver 117Procedure To adjust the parameters, proceed in the following manner: Step Action1 Code the number of the rack on the X-BUS.2 Code

PCIWAY driver118

119VIIModbus driverAt a GlanceSubject of this PartThis part describes how to install the Modbus driver for the Windows 98, Windows 2000\XP and Win

General information concerning the Drivers12 InstallationAt a Glance It is generally possible to launch the installation of all the drivers using th

Modbus driver120

12110InstallationAt a GlanceSubject of this ChapterThis chapter describes Modbus driver installation. This installation procedure can be broken do

Installation122 How to install the driverAt a Glance Driver installation is a standard installation. It can be launched either:from the drivers’ CD-

Installation 123How to install the driverTo install the driver, carry out the following procedure: Start of installationInstallation byCD-ROM?Inser

Installation124 Driver configuration screenAt a Glance The configuration tool is not outside the driver, but constitutes an embedded graphic interfa

Installation 125Description This table describes the different areas which make up the configuration screen:Modbus Instances Once installed, config

Installation126 Driver control screenAt a Glance This screen is used to view information concerning driver operation. The refreshment period for thi

Installation 127Description This table describes the different information concerning driver operation:Element Description Mode Displays the drive

Installation128 Driver debug screenAt a Glance This screen is used to deactivate the saving of certain operations carried out by the communication d

Installation 129Description This table describes the different areas which make up the debug screen:Area Description Refresh Period Allows the scr

General information concerning the Drivers 134 Then click on OK to confirm your choice.Result: the Safety warning window appears.5 Click on Yes to

Installation130 Information screenAt a Glance This screen provides general information on the communication driver and on the operating system insta

131VIIIUSB driverAt a GlanceSubject of this PartThis part describes how to install the USB driver for the Windows 2000\XP operating systems.What’s

USB driver132

13311InstallationAt a GlanceSubject of this ChapterThis chapter describes USB driver installation. This installation procedure can be broken down

Installation134 How to install the driverAt a Glance Driver installation is a standard installation. It can be launched either:from the drivers’ CD-

Installation 135Checks When using Windows 2000\XP, you must check whether it is possible to install unsigned drivers on the station.To do this, pe

Installation136 How to install the driverBefore starting the installation, check that the USB cable is not connected to the PLC.To install the drive

Installation 137Configuration screens for Win 2000\XPAt a Glance After rebooting the PC you will have to configure the USB driver, the USB cable m

Installation138 3 An icon is displayed in the task bar. Double clicking on it when the USB link with the PLC is operational calls up the window. Cli

Installation 139State of the USB linkAt a Glance This window informs the user of the state of the driver: Description:Field DescriptionVirtual Port

General information concerning the Drivers14 The drivers and Unity ProPrecautions To ensure correct operation of the drivers using the Unity Pro sof

Installation140

141IXDrivers managerAt a GlanceSubject of this PartThis part describes the Drivers manager tool that is used to configure the different drivers in

Drivers manager142

14312FunctionsManagement of X-Way driversAt a Glance The X-WAY drivers can be accessed using the Drivers Manager management tool.This is used to i

Functions144 X-Way Test tab This tab is used to test the basic operation of an X-Way driver: The table below describes the different zones of the w

Functions 145Modbus Test tab This tab is used to test the basic operation of a Modbus driver: The table below describes the different zones of the

Functions146 Other tabs The windows corresponding to these tabs are described in the description of the configuration for each driver:for the Uni-T

147AppendicesAt a GlanceSubject of this PartThis part describes the installation and configuration of drivers for the cable TSX PCX 3030 with wind

Appendices148

149AThe drivers of the TSX PCX 3030 cableAt a GlanceSubject of this ChapterThis Chapter describes the installation and configuration of drivers fo

15IIUni-Telway driversAt a GlanceSubject of this PartThis part describes how to install the drivers associated with Uni-Telway communication for W

TSXPCX3030150 Installing the drivers of the TSX PCX 3030 cableAt a Glance The TSX PCX 3030 cable is a USB/RS485 link converter. It enables a device

TSXPCX3030 151Installation The following table describes the procedure to install both drivers required to use the TSX PCX 3030 cable.Step Action1

TSXPCX3030152 3 Choose the Automatic driver search option and click on Next.Result: The following window is displayed: 4 Before selecting the CDROM

TSXPCX3030 15312 Click on Next.Result: a window indicates that the installation has been successfully completed.13 Click on Finish.Result: installa

TSXPCX3030154 Configuration screens for drivers using the TSX PCX 3030 cable.At a Glance Once the drivers of the TSX PCX 3030 cable are installed, y

TSXPCX3030 155Modbus Driver The following table describes the procedure for declaring the cable with a Modbus driver.Step Action1 From the Drivers

TSXPCX3030156

CBA 157DDrivers ManagementManagement of X-Way drivers, 143EEthwayConfiguration, 73Installation for Win 2000XP, 68Installation for Win NT, 71FFIP wi

Index158 TTSX PCX 3030Configuration screens, 154Installation, 150UUni-Telway on Serial portConfiguration screens, 20How to configure the driver, 24I

Uni-Telway drivers16

172Serial portAt a GlanceSubject of this ChapterThis chapter describes installation of the Uni-Telway driver communicating in slave mode on the se

Serial port18 How to install the driverAt a Glance Driver installation is a standard installation. It can be launched either:from the drivers’ CD-RO

Serial port 19How to install the driverTo install the driver, carry out the following procedure: Start of installationInstallation byCD-ROM?Insert

2

Serial port20 Driver configuration screensAt a Glance The configuration tool is used to link a driver configuration profile to a remote device that

Serial port 21Uni-Telway parametersThe parameters are presented in the following manner: The Station ID window is used to name the remote device

Serial port22 Line parameters The parameters are presented in the following manner: This tab is used to configure the parameters linked to transmiss

Serial port 23Advanced parametersThe parameters are presented in the following manner: This tab is used to configure the line type:PC: uses the dri

Serial port24 How to configure the driverAt a Glance During driver installation, a default profile is proposed. This profile can be modified or a ne

Serial port 25How to modify a profileFrom the driver configuration screen.How to remove a profileFrom the driver configuration screen.How to activa

Serial port26

273TSX SCP 114 cardAt a GlanceSubject of this SectionThis chapter describes installation of the Uni-Telway driver communicating in slave mode via

TSX SCP 114 card28 How to install the driverAt a Glance Driver installation is a standard installation. It can be launched either:from the drivers’

TSX SCP 114 card 29How to install the driverTo install the driver, carry out the following procedure: Start of installationInstallation byCD-ROM?In

3Table of ContentsAbout the Book. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7Part I General information on the instal

TSX SCP 114 card30 Driver configuration screensAt a Glance The configuration tool is used to configure the TSX SCP 114 card Uni-Telway driver.Illust

TSX SCP 114 card 31Line parameters The parameters are presented in the following manner: This tab is used to configure the parameters linked to tra

TSX SCP 114 card32 Configuration of the Windows 98 operating systemAt a Glance After the driver installation and configuration phase, the operating

TSX SCP 114 card 33Configuration of the Windows 2000\XP operating systemAt a Glance After the driver installation and configuration phase, the oper

TSX SCP 114 card34 Configuration of Win NT operating systemAt a Glance After the driver installation and configuration phase, the operating system s

35IIIFIP driversAt a GlanceSubject of this PartThis part describes how to install the drivers associated with FIP communication for Windows 98, Wi

FIP drivers36

374TSX FPP 20 cardAt a GlanceSubject of this ChapterThis chapter describes installation of the driver used to communicate in Fipway\Fipio mode via

TSX FPP 20 card38 How to install the driverAt a Glance Driver installation is a standard installation. It can be launched either:from the drivers’ C

TSX FPP 20 card 39How to install the driverTo install the driver, carry out the following procedure: Start of installationInstallation byCD-ROM?Ins

4Configuration of the Windows 2000\XP operating system. . . . . . . . . . . . . . . . . . 42Configuration of the Windows NT operating system . . . . .

TSX FPP 20 card40 How to install the driverAt a Glance The configuration tool is used to configure the driver in Fipway or Fipio mode to use the TSX

TSX FPP 20 card 41Configuration of the Windows 98 operating systemAt a Glance After the driver installation and configuration phase, the operating

TSX FPP 20 card42 Configuration of the Windows 2000\XP operating systemAt a Glance After the driver installation and configuration phase, the operat

TSX FPP 20 card 43Configuration of the Windows NT operating systemAt a Glance After the driver installation and configuration phase, the operating

TSX FPP 20 card44

455TSX FPC 10 ISA cardAt a GlanceSubject of this ChapterThis chapter describes installation of the driver communicating in Fipway/Fipio mode via t

TSX FPC 10 ISA card46 How to install the driverAt a Glance Driver installation is a standard installation. It can be launched either:from the driver

TSX FPC 10 ISA card 47How to install the driverTo install the driver, carry out the following procedure: Start of installationInstallation byCD-ROM

TSX FPC 10 ISA card48 Driver configuration screen for Windows NTAt a Glance The configuration tool is used to configure the driver in Fipway or Fipi

TSX FPC 10 ISA card 49Advanced configurationTo access the advanced configuration screen use the commands "File->Advanced Configuration&quo

5How to adjust the ISA TPCX 57 card parameters. . . . . . . . . . . . . . . . . . . . . . . 108Chapter 9 PCIWAY driver for TSX PCI 57 ••• processors .

TSX FPC 10 ISA card50 Driver configuration screen for Windows 98\2000\XPAt a Glance The configuration tool is used to configure the driver in Fipway

TSX FPC 10 ISA card 51Configuration of the operating system using the TSX FPC 10 cardAt a Glance After the driver installation and configuration p

TSX FPC 10 ISA card52 How to select the hardware type for Windows 98Procedure After having installed and configured the driver, carry out the follow

TSX FPC 10 ISA card 532Answer No to the question Do you want Windows to search for your new hardware?ResultThe following window appears: 3 Select F

TSX FPC 10 ISA card54 5 Click on Next.6Answer No to the question Do you want to restart your computer now?ResultThe following window appears and the

TSX FPC 10 ISA card 55How to select the hardware type for Windows 2000\XPProcedure After having installed and configured the driver, carry out the

TSX FPC 10 ISA card56 2 Select the option Add/Troubleshoot a peripheral then click Next.ResultThe following window appears: 3 Select the option Add

TSX FPC 10 ISA card 575 Click on Next.ResultThe following window appears: 6 Select FPC10 Device from the list then click on Next.7 Select FPC10 WDM

TSX FPC 10 ISA card58 How to configure hardware parameters for Windows 98Procedure When you want to modify the hardware parameters, carry out the fo

TSX FPC 10 ISA card 594 Click on Change settings.ResultThe following window appears: 5 From the Value list, select the non-conflicting address rang

6

TSX FPC 10 ISA card60 How to configure hardware parameters for Windows 2000\XPProcedure After having selected the hardware type, carry out the follo

TSX FPC 10 ISA card 615 Click on Change settings. ResultThe following window appears: 6 From the Value list, select the non-conflicting address ran

TSX FPC 10 ISA card62 10 Accept the configuration with OK.ResultThe following window appears: 11 Click on Finish to confirm hardware configuration.S

TSX FPC 10 ISA card 63How to adjust the ISA TSX FPC 10 card parametersAt a Glance Before installing the TSX FPC 10 card, you must adjust the follow

TSX FPC 10 ISA card64 Procedure To adjust the parameters, proceed in the following manner: Example of IRQ selectionThe interrupt address provided by

65IVETHWAY driverAt a GlanceSubject of this PartThis part describes how to install the drivers associated with ETHWAY communication for Windows 20

ETHWAY driver66

676InstallationAt a GlanceSubject of this ChapterThis driver is used to communicate via an Ethernet card using the ETHWAY protocol. Driver install

Installation68 How to install the driver for Windows 2000\XPAt a Glance The ETHWAY protocol is installed from:from the drivers’ CD-ROM,or from disks

Installation 69How to install the driverThe ETHWAY driver is installed in accordance with the following procedure:Step Action1 Insert the CD-ROM or

7About the BookAt a GlanceDocument Scope This document deals with the installation of communication drivers for Windows 98, Windows 2000/XP and Wi

Installation70 6 In the Select Network Component Type window, select the type Protocol then click on Add.ResultThe following window appears: 7 Click

Installation 71How to install the driver for Windows NTAt a Glance The ETHWAY protocol is installed from:from the drivers’ CD-ROM,or from disks if

Installation72 How to install the driverThe ETHWAY driver is installed in accordance with the following procedure:Step Action1 Insert the CD-ROM or

Installation 73Driver configuration toolAt a Glance The configuration tool is used to configure the Ethernet card to communicate according to the E

Installation74 Description This table describes the different areas which make up the configuration screen:Number Element1 This field is used to sel

75VXIP driver on TCP/IPAt a GlanceSubject of this PartThis part describes how to install the drivers associated with X-Way communication on TCP/IP

XIP driver on TCP/IP76

777InstallationAt a GlanceSubject of this ChapterThis driver is used to communicate via an Ethernet card using the X-Way protocol on TCP/IP.This c

Installation78 How to install the driverAt a Glance Driver installation is a standard installation. It can be launched either:from the drivers’ CD-R

Installation 79How to install the driverTo install the driver, carry out the following procedure: Start of installationInstallation byCD-ROM?Insert

About the Book8 Product Related WarningsSchneider Electric assumes no responsibility for any errors that may appear in this document. If you have an

Installation80 Driver configuration screenAt a Glance The configuration tool is used to link a driver configuration profile to a remote device that

Installation 81Description This table describes the different areas which make up the configuration screen:Number Element1 All software functions c

Installation82 How to configure the driverAt a Glance During driver installation, a default configuration profile is proposed. You are able to modif

Installation 83Example The architecture below describes the addressing of stations on Ethernet and Fipway networks: Access to stationsTo directly a

Installation84 How to remove a connectionFrom the configuration screen,How to modify a connectionFrom the configuration screen,XIP Instances Once in

85VIDrivers for Atrium ProcessorsAt a GlanceSubject of this PartThis part describes how to install the drivers associated with the TPCX 57 and TSX

Drivers for Atrium Processors86

878ISAWAY driver for TPCX 57 processorsAt a GlanceSubject of this ChapterThis driver makes it possible to use the TPCX 57 processor on the ISA bus

ISAWAY driver88 How to install the driverAt a Glance Driver installation is a standard installation. It can be launched either:from the drivers’ CD-

ISAWAY driver 89How to install the driverTo install the driver, carry out the following procedure: Start of installationInstallation byCD-ROM?Inser

9IGeneral information on the installation of driversAt a GlanceSubject of this PartThis part describes the installation principle of the various d

ISAWAY driver90 Configuration of the ISAWAY driver for Windows NTAccess to the configuration toolThe configuration tool can be accessed from the tas

ISAWAY driver 91Driver configurationPress the Configuration button to display the following window: The table below describes the different command

ISAWAY driver92 Click the tab "Driver" to display the following window: This window displays general information on the driverPCX57 Conf

ISAWAY driver 93Properties Press the Properties button to display the following window: The table below describes the different areas:Area Descript

ISAWAY driver94 Click the Datagram tab to display the following window: The table below describes the different areas:Area Description Input/Output

ISAWAY driver 95Configuration of ISAWAY driver for Windows 98\2000\XPAt a Glance The management tool tab is as follows: Elements The Properties but

ISAWAY driver96 Configuration of the operating systemAt a Glance After the driver installation and configuration phase, the operating system shall r

ISAWAY driver 97How to select the hardware type for Windows 98Procedure After having installed and configured the driver, carry out the following p

ISAWAY driver98 2Answer No to the question Do you want Windows to search for your new hardware?ResultThe following window appears: 3 Select PCX57 De

ISAWAY driver 995 Click on Next.6Answer No to the question Do you want to restart your computer now?ResultThe following window appears and the card